• Skip to main content
  • Skip to primary sidebar

Making Easy Circuits

Learn and build electronic circuits

You are here: Home / Motor Driver / High Current Motor Speed Controller Driver Circuit

High Current Motor Speed Controller Driver Circuit

Last Updated on February 22, 2021 by Admin Leave a Comment

This straightforward circuit is developed for controlling all forms of high current DC motors that is rated up to 40 A. Fundamentally, it’s just a standard oscillator triggering a handful of power MOSFETs.

The oscillator is a basic RC-type about a sole Schmitt trigger component (IC1a) from a 40106 hex inverter package. When the wiper is actuated in the direction of D2, potentiometer P1 provides peak voltage to the output. The two diodes safeguard the circuit from short-circuiting the output to the input. At the limits of P1, there are minimal discharge and charge times. We found the negative-sliding pulse is about 1 µs and 1.6 µs for the positive side when evaluating the prototype.

high current DC motor driver compressed

Inverters IC1b and IC1c filters the oscillator signal and ramps a buffer stage which contains three inverters connected in parallel, IC1d, IC1e and IC1f. To contain the MOSFETs in the absence of 40106, resistor R1 was included. The sum of the input drive capacitance of the four MOSFETs is close to 8 nF.

This value is excessive for the buffer to fully charge and discharge when P1 is switched to its extreme points. In a way, this is useful because practically it permits the high current motor driver to control the full output voltage span of from 0% to 100%.

The operating frequency set for this circuit is 1 kHz but, on the prototype, 1.07 kHz was recorded. Diode D3 at the output limits the reverse energy (back emf) produced by inductive loads which are all the DC motors. Substantial output currents and back emf are problems.

When testing with an earlier prototype, the rails to D3 were too slim. Furthermore, when experimenting the high current motor driver circuit with one of the motors, one of the rails suffered a burnout. Both motors used in the Wheelie when fully loaded consumes 20 A at 24 V. the circuit was examined at 40 A and 24 V with a resistive load.

Still, the constructed PCB was not able to manage such extreme currents. One of the solutions is to enhance the copper rails channelling high current flow with 13 or 14 AWG (2.5 mm2) copper cables.

Two paralleled parts of 16 AWG (around 1.5 mm2) may be more convenient to fit them into place. Because of that, the PCB is void of solder stop masks. The layered lines in the schematic present an easy identification of the expected travel locations of the high currents. A 78L12 voltage regulator delivers power for the 40106 using its standard decoupling capacitors.

You may attach the speed--regulating potentiometer off the board and linked with simple wires. It is also recommended to attach a heatsink to the PCB with 3-mm (6 IBA) screws.

You have to ensure the heatsink is insulated with the solder pads for the MOSFETs. After that, find the right positions for the transistor mounting screws, and D3. You can bend the transistors’ legs using a special tool to avoid mechanical stress. Only then, you should locate the placements of for the holes. The threading for this hole is 3-mm (around 1/8”, 6 BA) so you must tap it accordingly.

We highly recommend you double-check if all the semiconductors are isolated on the heatsink. There is a possibility that you will hear a faint whine from the DC motor because of the low switching frequency. This is normal and nothing to worry about.

You'll also like:

  • 1.  How to Build a Brushless (BLDC) Motor Controller Circuit
  • 2.  Model Train Controller Circuit
  • 3.  Simple Drill Speed Controller Circuit – 220V, 120V AC Back EMF Dependent
  • 4.  How to Build a 3 Phase Brushless (BLDC) Motor Driver Circuit
  • 5.  Simple DC Motor Speed Controller Circuit
  • 6.  Automatic Sliding Door Circuit

About Admin

Hey friends, Thanks a bunch for stopping by this site! I am an engineer with a Bachelor of Engineering in Electronics and Telecommunication. One of my passions is gathering information from all sorts of electronics books and tutorials. I then take that information and compile it into a language that is super easy to understand. My goal is to make those complex electronics circuit concepts and technical terms much more accessible for all the new and budding electronics engineers out there. I can also design customized circuit diagrams as required by the users.
If you have any questions related to this field, please do not hesitate to drop a comment! I am always here and ready to help you out with any queries you might have. I cannot wait to hear from you!

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Primary Sidebar

Categories

  • 3 Phase (4)
  • 8051 Microcontroller (1)
  • Arduino (11)
  • Audio and Amplifier (102)
  • Automation (8)
  • Battery Chargers (64)
  • Bicycle Projects (4)
  • Car and Motorcycle Projects (39)
  • Datasheets (10)
  • DIY Projects (5)
  • Electrical (15)
  • Free Energy (6)
  • Games Projects (2)
  • High Voltage (14)
  • Hobby Projects (30)
  • Household Circuits (2)
  • IC 555 Circuits (4)
  • Ignition Circuits (2)
  • Indicators (50)
  • Infrared (6)
  • Inverter Circuits (29)
  • Lights and Lamps (97)
  • Medical (8)
  • Meter and Tester Circuits (38)
  • Motor Driver (17)
  • New Circuits (56)
  • Oscillators (30)
  • Pets and Pests (5)
  • Power supply (81)
  • Protection Circuits (25)
  • PWM (8)
  • Remote Control (20)
  • Security and Alarm Circuit (48)
  • Sensors and Detectors (66)
  • Signal Processor (23)
  • Solar Controller Circuits (61)
  • SSR (3)
  • Temperature Controller (20)
  • Timer (25)
  • Transformerless (7)
  • Transmitters (12)
  • Tutorials (45)
  • UPS (2)
  • Voltage Regulators (57)
  • Water Sensor and Controller (29)
  • Home
  • Privacy Policy
  • Contact
  • Disclaimer
  • Copyright

© 2025 · Making Easy Circuits